Oregon Scientific CP100 - Notice

CLOCK

To set the clock:

1. Press and hold

CLOCK

for 2 seconds. The setting

will blink.

2. Use / to change the setting.
3. Press

CLOCK

to confirm.

4.

The settings order is:

12 / 24 hour format, hour,

minute, year, month-day format, month and day.

LCD DISPLAY

Use motion above the IR motion sensors to toggle display

mode between:
• Clock
• Calendar
• Alarm
• Indoor temperature

NOTE

The IR motion sensors range is from 2.5 to 15 cm

(1 to 6 in) above the sensor. Any movement outside this
range will not be detected.

ALARM

To set the alarm:

1. Press

ALARM

or navigate to Alarm display.

2. Press and hold

ALARM

for 2 seconds to enter alarm

setting mode. The setting will blink.

3. Use / to change the setting for hour.
4. Press

ALARM

to confirm.

5. Repeat steps 3 and 4 to set minute. appears when

the alarm is set.

To silence the alarm:

• Use motion above the IR motion sensors to activate

the 8-minute

SNOOZE

feature.

OR

• Press

ALARM, CLOCK

, or to mute the alarm

and automatically activate the alarm again after 24

hours.

To activate / deactivate the alarm:

• Press

ALARM ON / OFF

.

PROJECTION

The ultra-bright LED enables daylight projection of time

and temperature information.

To activate projection:

Slide

PROJECTION

to

AUTO

or

CLOCK

.

• Slide to

AUTO

to toggle between current time and

indoor temperature.

• Slide to

CLOCK

to project current time only.

To adjust the projection image:

• Switch

CDS

to

ON

to activate automatic projection

dimming.

• Press

180° ROTATION

to rotate the image by 180°.

• Focus the projector image by turning the

FOCUS

wheel.

NOTE

Please take care not to look into the projector.

Oregon Scientific will not be held responsible for any

results or consequences arising from the misuse of this

product.

TEMPER ATURE

Press

°C / °F

to select the temperature display unit.

RESET

To return the unit to the default settings, insert a thin blunt

object into the

RESET

hole.

PRECAUTIONS

This product is engineered to give you years of

satisfactory service if you handle it carefully. Here are a

few precautions:

• Do not cover the ventilation holes. Make sure items

that are nearby such as newspapers, tablecloths,

curtains etc cannot accidentally cover the ventilation

holes.

• Placement of this product on wood surfaces with

certain types of finishes, such as clear varnish, may

result in damage to the finish. Consult the furniture

manufacturer’s care instructions for direction as to

the types of objects that may safely be placed on

the wood surface. Oregon Scientific shall not be

responsible for any damage to wood surfaces from

contact with this product.

• Do not immerse the unit in water. If you spill liquid

over it, dry it immediately with a soft, lint-free cloth.

• Do not clean the unit with abrasive or corrosive

materials. This may scratch the plastic parts and

corrode the electronic circuit.

• Do not subject the unit to excessive force, shock,

dust, temperature or humidity, which may result in

malfunction, shorter electronic life span, damaged

battery and distorted parts.

Daylight Projection Clock

Model: DP100

USER MANUAL

INTRODUCTION

Thank you for selecting the Oregon Scientific

TM

daylight

projection clock (DP100).

NOTE

Please keep this manual handy as you use

your new product. It contains practical step-by-step

instructions, as well as technical specifications and

warnings you should know about.

OVERVIEW

FRONT VIEW

2

3

4

1

6

5

1.

CDS light sensor:

Adjusts projection brightness

2.

ALARM ON / OFF:

Activate / deactivate alarm

3.

LCD display:

Clock, alarm, calendar and indoor

temperature

4.

:

Alarm icon

5.

IR motion sensors:

Snooze; change display mode

6.

Projector:

Projects time, alarm status and indoor

temperature

BACK AND BASE VIEW

1

2
3

6

7

8

9
10

4

5

1.

FOCUS:

Focus the projected image

2. Temperature sensor and adapter slot
3.

CLOCK:

Enter clock setting mode

4.

/

:

Increase / decrease setting

5.

PROJECTION OFF / CLOCK / AUTO:

Select

projection mode

6.

ALARM:

Enter alarm setting mode

7.

180° ROTATION:

Rotate projection image by 180°

8.

°C / °F:

Select temp erature unit

9.

RESET:

Return to default settings

10.

CDS ON / OFF:

Activate light sensor

GETTING STARTED

ADAPTER

Insert the adapter into the adapter slot as shown.

EN

• Do not tamper with the unit’s internal components.

Doing so will invalidate the warranty on the unit and

may cause unnecessary damage. The unit contains

no user-serviceable parts.

• Do not dispose this product as unsorted municipal

waste. Collection of such waste separately for special

treatment is necessary

• Due to printing limitations, the displays shown in this

manual may differ from the actual display.

• The contents of this manual may not be reproduced

without the permission of the manufacturer.

NOTE

The technical specifications for this product and

the contents of the user manual are subject to change

without notice.

SPECIFICATIONS

TYPE

DESCRIPTION

Unit dimension

138 x 88 x 44 mm

(H x W x D)

(5.4 x 3.5 x 1.7 in)

Unit weight

523g (18.4 oz)

Clock format

12 / 24-hour

Alarm duration

2 min

Snooze

8 min

Temperature range

0°C to 50°C

(32°F to 122°F)

Temperature resolution

1°C (1°F)

Projector rotation angle

+ / - 90°

IR sensor coverage distance

2.5 to 15 cm

(1 to 6 in)

Power

DC 5.0V adapter

ABOUT OREGON SCIENTIFIC

Visit our website (www.oregonscientific.com) to learn

more about Oregon Scientific products such as digital

cameras; MP3 players; children’s electronic learning

products and games; projection clocks; health and

fitness gear; weather stations; and digital and conference

phones. The website also includes contact information

for our Customer Care department in case you need

to reach us, as well as frequently asked questions and

customer downloads.
We hope you will find all the information you need on our

website, however if you’re in the US and would like to

contact the Oregon Scientific Customer Care department

directly, please visit:
www2.oregonscientific.com/service/default.asp
OR

Call 1-800-853-8883.
For international inquiries, please visit:

www2.oregonscientific.com/about/international.asp

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired

operation.

WARNING

Changes or modifications not expressly

approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

NOTE

This equipment has been tested and found

to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against

harmful interference in a residential installation.
This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV

technician for help.

DECLARATION OF CONFORMITY

The following information is not to be used as contact

for support or sales. Please call our customer service

number (listed on our website at

www.oregonscientific.com), or on the warranty card for

this product) for all inquiries instead.

We

Name:

Oregon Scientific, Inc.

Address:

19861 SW 95th Ave.,

Tualatin, Oregon 97062 USA

Telephone No.:

1-800-853-8883

declare that the product

Product No.:

DP100

Product Name:

Daylight Projection Clock

Manufacturer:

IDT Technology Limited

Address:

Block C, 9/F, Kaiser Estate,

Phase 1,41 Man Yue St., Hung

Hom, Kowloon, Hong Kong

is in conformity with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: 1) This device

may not cause harmful interference. 2) This device must

accept any interference received, including interference

that may cause undesired operation.

INTRODUCTION

Merci d’avoir sélectionné l’Horloge à Projection de Jour

de Oregon Scientific

TM

. (Modèle DP100).

REMARQUE

Veuillez conserver ce manuel pour toutes

références ultérieures. Il contient toutes les instructions

pratiques, les caractéristiques techniques et les

avertissements à prendre en compte.

VUE D’ENSEMBLE

FACE AVANT

2

3

4

1

6

5

1.

Capteur de lumière CDS:

Ajuste la clarté de

projection

2.

ALARM ON / OFF:

Permet d’activer / désactiver

l’alarme

3.

Affichage LCD:

Horloge, alarme, calendrier et

température intérieure.

4.

:

Icône de l’alarme

5.

Capteurs de mouvement infra rouge:

Snooze

(Rappel d’alarme) ; changement du mode

d’affichage

6.

Projecteur:

Permet de projeter l’heure, l’état de

l’alarme et la température intérieure

VUE DE DOS ET VUE INFERIEURE

1

2
3

6

7

8

9
10

4

5

1.

FOCUS:

Permet de mettre au point l’image du

projecteur

2. Capteur de température et prise adaptateur
3.

CLOCK:

Permet d’entrer dans le mode réglage de

l’horloge

4. / : Permet d’augmenter / diminuer les valeurs de

réglage.

5.

PROJECTION OFF / CLOCK / AUTO:

Permet de

sélectionner le mode de projection

6.

ALARM:

Permet d’entrer dans le mode réglage de

l’alarme

7.

180° ROTATION:

Permet de faire tourner l’image à

180°

8.

°C / °F:

Permet de sélectionner l’unité de mesure de

la température

FR

9.

RESET:

Permet de revenir aux réglages par défaut

10.

CDS ON / OFF:

Permet d’activer le capteur de

lumière

AU COMMENCEMENT

ADAPTATEUR

Branchez l’adaptateur dans la prise adaptateur comme

indiqué.

HORLOGE

Pour régler l’horloge :

1. Appuyez et maintenez enfoncée la touche

CLOCK

pendant 2 secondes. Le réglage clignotera.

2. Utilisez / pour changer le réglage
3. Appuyez sur

CLOCK

pour confirmer.

4. L’ordre de réglage est le suivant : Format 12/24

heures, heure, minutes, année, format mois/jour,

mois et jour.

AFFICHAGE LCD

Utilisez le signe situé au dessus des capteurs de

mouvement infra rouge pour alterner entre les modes

suivants :
• Horloge
• Calendrier
• Alarme
• Température intérieure

REMARQUE

La portée des capteurs de mouvement

infra rouge est de 2,5 à 15 cm (1 à 6 pouces) au dessus

du capteur. Tout mouvement hors de cette portée ne

sera pas détecté.

ALARME

Pour régler l’alarme :

1. Appuyez sur

ALARM

ou entrez dans l’affichage de

l’Alarme

2. Appuyez et maintenez enfoncée la touche

ALARM

pendant 2 secondes pour entrer dans le mode de

réglage de l’alarme. Le réglage clignotera.

3. Utilisez / pour changer le réglage de l’heure
4. Appuyez sur

ALARM

pour confirmer.

5. Répétez les étapes 3 et 4 pour régler les minutes

s’affichera une fois l’alarme réglée.

Pour couper le son de l’alarme :

• Utilisez le signe situé au dessus des capteurs de

mouvement infra rouge pour activer la fonction

SNOOZE

(rappel d’alarme) de 8 minutes.

OU

• Appuyez sur

ALARM, CLOCK,

ou pour couper

le son de l’alarme et la réactiver automatiquement 24

h plus tard.

Pour activer / désactiver l’alarme :

• Appuyez sur

ALARM ON / OFF

.

PROJECTION

La forte clarté de la diode électroluminescente permet une

projection en journée de l’heure et de la température.
Pour activer la projection :
Placez l’encoche

PROJECTION

sur

AUTO

ou sur

CLOCK

.

• Placez l’encoche sur

AUTO

pour alterner entre

l’heure actuelle et la température intérieure.

• Placez l’encoche sur

CLOCK

pour ne projeter que

l’heure actuelle.

Pour ajuster l’image projetée :

• Placez

CDS

sur

ON

pour activer la gradation de

projection automatique.

• Appuyez sur

180° ROTATION

pour faire tourner

l’image à 180°.

• Tournez la molette

FOCUS

pour mettre au point

l‘image projetée.

REMARQUE

Faîtes attention à ne pas regarder dans

le projecteur. Oregon Scientific ne sera en aucun cas

responsable des conséquences ou résultats découlant

de la mauvaise utilisation de ce produit.

TEMPER ATURE

Appuyez sur

°C / °F

pour sélectionner l’unité d’affichage

de la température.

DP100 MANUAL (E-F-ES).indd 1

5/19/06 4:18:37 PM

P/N: 086L004396-020 REV1

1/2