Dewalt DW890 - Mode d'emploi

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

DW890, DW891

Swivel Head Shears

Cisailles à tête pivotante

Cizalla de cabezal giratorio

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA.

ADVERTENCIA:

LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.

DANGER:

Indicates an imminently hazardous situation which, if not

avoided,

will

result in

death or serious injury

.

WARNING:

Indicates a potentially hazardous situation which, if not

avoided,

could

result in

death or serious injury

.

CAUTION

: Indicates a potentially hazardous situation which, if not

avoided,

may

result in

minor or moderate injury

.

CAUTION:

Used without the safety alert symbol indicates a poten-

tially hazardous situation which, if not avoided,

may

result in

property

damage

.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D

E

WALT TOOL,

CALL US TOLL FREE AT:

1-800-4-D

E

WALT (1-800-433-9258)

General Safety Rules – For All Tools

WARNING!

Read all instructions. Failure to follow all instructions listed below

may result in electric shock, fire and/or serious injury. The term “power tool” in all

of the warnings listed below refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and

matching outlets will reduce risk of electric shock

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators.

There is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will

increase the risk of electric shock

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged

or entangled cords increase the risk of electric shock. Replace or repair damaged cords.
Make sure your extension cord is in good condition. Use only 3-wire extension cords that
have 3-prong grounding-type plugs and 3-pole receptacles that accept the tool’s plug.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use.

Use of a cord suitable for outdoor use reduces the risk of electric shock. When using

an extension cord, be sure to use one heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line voltage resulting in loss of power and
overheating. The following table shows the correct size to use depending on cord length
and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the
gauge number, the heavier the cord.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

120V

0-25

26-50

51-100

101-150

240V

0-50 51-100

101-200

201-300

Ampere Rating

More

Not

more

AWG

Than Than
0

-

6

18

16

16

14

6

-

10

18

16

14

12

10

-

12

16

16

14

12

12

-

16

14

12

Not Recommended

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication.

A moment of inattention while operating power toolsmay

result in serious personal injury.

b) Use safety equipment. Always wear eye protection.

Safety equipment such as

dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in the off-position before plugging

in.

Carrying power tools with your finger on the switch or plugging in power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.

A wrench or

a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times.

This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewellery or long hair can be caught

in moving parts. Air vents often cover moving parts and should also be avoided.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used.

Use of these devices can reduce dust-

related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for your application.

The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off.

Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power

tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tools operation. If
damaged, have the power tool repaired before use.

Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions and in the manner intended for the particular type of power tool, taking
into account the working conditions and the work to be performed.

Use of the power

tool for operations different from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

Additional Safety Rules Instructions for Shears

• Hold tool by insulated gripping surfaces when performing an operation where the cut-

ting tools may contact hidden wiring or its own cord.

Contact with a “live” wire will make

exposed metal parts of the tool “live” and shock the operator.

• Cut material at or below rated capacity. Remember, material thickness increases as

gauge number deceases (14 gauge is thicker than 16 gauge). 14 gauge thickness is
.075" (1.9 mm); 16 gauge is .060" (1.5 mm).

• NEVER have any part of your body near the blades.

Serious personal injury may result.

• Keep hands away from cutting area.

A moment of inattention while operating power tools

may result in serious personal injury.

• ALWAYS

wear gloves when handling sheet metal. The edges are sharp and can cause seri-

ous personal injury.

• Firmly secure the piece of metal to be cut

to prevent movement during cutting.

• ALWAYS start tool before engaging material

to be cut.

• ALWAYS use tool with curl deflector.
• If possible, cut material so scrap curl is to the right.

This direction will move curl down

and out of the way.

• Use

shears

upright.

If tool is upside down, metal curl may turn toward you.

• DO

NOT

use the shear with any kind of accessory or attachment.

• Always wear safety shoes

to protect your feet from sharp metal debris on the floor.

• Keep all screws tight.

Check periodically for loosening.

• Do

not

place anything into the motor housing openings.

• Clean out your tool often, especially after heavy use.

Dust and grit containing metal

particles often accumulate on interior surfaces and could create an electric shock hazard.

• Stay clear of end pieces that may fall after being cut off.

Contact with a sharp edge could

result in personal injury.

• Always keep the power cord away from the edge of the material being cut.

Sharp edges

can result in the cord insulation being cut. This condition may create an electrical hazard.

WARNING: ALWAYS

use safety glasses. Everyday eyeglasses are NOT safety glasses.

Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3)
• ANSI S12.6 (S3.19) hearing protection
• NIOSH/OSHA/MSHA

respiratory

protection.

WARNING: Always use eye protection.

All users and bystanders must wear eye protection

that conforms to ANSI Z87.1.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.
•

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water.

Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING:

Use of this tool can generate and/or disburse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body.
• The label on your tool may include the following symbols. The symbols and their definitions

are as follows:

V .................. volts A

.................... amperes

Hz ................ hertz W

................... watts

min .............. minutes

.................. alternating current

D

E

WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286.

(APR07) Form No. 649915-00 DW890, DW891

Copyright © 1997, 2002, 2007 D

E

WALT

The following are trademarks for one or more D

E

WALT power tools: the yellow and black color scheme; the

“D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of
lozenge-shaped humps on the surface of the tool.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D

E

WALT • www.dewalt.com