American Standard 8040.23 - Notice

Certified to comply with ANSI A112.18.1

Certificación de cumplimiento de la norma ANSI A112.18.1

Certifié conforme à ANSI A112.18.1

U.S. Patent No. D403,750

Patente estadounidense D403,750

Brevet U.S.A. no. D403,750

T I S S U E H O L D E R

S O P O R T E PA R A PA P E L H I G I É N I C O

S U P P O R T D E PA P I E R T O I L E T T E

M 9 6 8 74 2 R E V. 1. 2

8 0 4 0 . 2 3 0 S E R I E S

S E R I E 8 0 4 0 . 2 3 0

S É R I E 8 0 4 0 . 2 3 0

Gracias por seleccionar los productos American Standard, sinónimo de la mejor calidad

durante más de 100 años. Por favor lea estas instrucciones detenidamente antes de

comenzar para que lleve a cabo la instalación sin contratiempos.

Nous vous remercions d’avoir choisi American Standard… synonyme de qualité supérieure

depuis plus de 100 ans. Pour vous assurer que l’installation se déroulera sans difficulté,

veuillez lire attentivement ces instructions avant de commencer.

Thank you for selecting American-Standard...the benchmark of fine

quality for over 100 years. To ensure that your installation proceeds smoothly--

please read these instructions carefully before you begin.

Instrucciones de instalación

Mode d’installation

Installation Instructions

Regular Screwdriver
Desarmador plano

Tournevis plat

Recommended Tools & Materials/Herramientas y Materiales Recomendados/Outils et matériaux recommandés

Phillips Screwdriver

Desarmador de cruz

Tournevis cruciforme

10'

Tape Measure
Flexómetro
Ruban à mesurer

Drill
Taladro
Perceuse

1

1

INSTALL MOUNTING PLATES

6-1/4"

6-1/4" (159 mm)

159 mm (6-1/4 po.)

The TISSUE HOLDER (1) works best if secured to a wall stud or cross brace within the wall, using the SCREWS (3) supplied.
If the TISSUE HOLDER (1) is to be installed on a tile or plaster wall the ANCHORS (4) and SCREWS (3) should be used.

Determine desired height and location (optional) and mark a center line. Using the MOUNTING PLATE (5) as a template mark the two

spots for the mounting holes. If MOUNTING PLATE (5) is secured to a stud or cross brace drill small pilot holes for SCREWS (3).

Secure MOUNTING PLATE (5) to wall with SCREWS (3).

Note: The center line distance (6-1/4") between the MOUNTING PLATES (5) is critical, and must be maintained.

USE MOUNTING PLATE AS TEMPLATE

USE LA PLACA DE MONTAJE COMO PLANTILLA

UTILISER UNE PLAQUE DE MONTAGE COMME GUIDE

5

4

3

CENTER LINE

LÍNEA CENTRAL

LIGNE CENTRALE

FINISHED WALL

PARED TERMINADA

MUR FINI

2

CENTER LINE

LÍNEA CENTRAL

LIGNE CENTRALE

For installations on drywall,

use DRYWALL ANCHORS (6) and SCREWS (3) for securing MOUNTING PLATE (5) to wall. Place #2 Phillips

screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush

with the wall. The TISSUE HOLDER BODIES (2) are mounted 6-1/4" center to center. Place MOUNTING PLATE (5) over DRYWALL

ANCHORS

(6) and insert SCREWS (3) with #2 Phillips screwdriver. See illustration below. Repeat above steps for remaining

MOUNTING PLATES (5).

For installations on tiled walls,

If TILE ANCHORS (4) and SCREWS (3) are used for securing MOUNTING PLATE (5), then drill

two 1/4" diameter holes a minimum of 1-1/4" deep. Insert the two TILE ANCHORS (4) flush with face of the finished wall. The TISSUE

HOLDER BODIES (2) are mounted 6-1/4" center to center. Place MOUNTING PLATE (5) over TILE ANCHORS (4) and insert screws

provided with #2 Phillips screwdriver. See illustration below. Repeat above steps for remaining MOUNTING PLATES (5).

5

6

4

4

6

3